NZMH1-S80-SVE
112808 NZMH1-S80-SVE
112808

Devre kesici, 3p, 80A, takılabilir modül
NZM..-S serisi devre kesiciler yalnızca dört kompakt boyutuyla tüm uygulama durumlarını kapsar ve IEC pazarına uygundur. Modüler fonksiyon grupları montajı her zaman esnek hale getirir. Aşırı yük rölesi ile bağlantılı olarak manyetik kısa devre bobini ile. Aşırı yük tetiklemesiz kısa devre bırakmalı. Notlar: devre kesiciler AC-3 anahtarlama kategorisinin tüm gereksinimlerini karşılar.

Product range	Circuit-breaker
Protective function	Short-circuit protection
Standard/Approval	IEC
Installation type	Plug-in units
Release system	Thermomagnetic release
Construction size	NZM1
Description	Motor protection in conjunction with overload relay With short-circuit release Without overload release Ir IEC/EN 60947-4-1, IEC/EN 60947-2 The circuit-breaker fulfills all requirements for AC-3 switching category.
Number of poles	3 pole
Standard equipment	Box terminal
Rated current = rated uninterrupted current [In = Iu]	80 A
400/415 V 50 Hz [Icu ]	100 kA
Short-circuit releases [Irm ] >Non-delayed [Ii = In x …]	8 - 14
380 V 400 V [P]	37 kW
400 V [Ie ]	68 A
Standards	IEC/EN 60947
Protection against direct contact	Finger and back of hand proof to VDE 0106 Part 100
Climatic proofing	Damp heat, constant, to IEC 60068-2-78 Damp heat, cyclic, to IEC 60068-2-30
Ambient temperature >Ambient temperature, storage	- 40 - + 70 °C
Ambient temperature >Operation	-25 - +70 °C
Mechanical shock resistance (10 ms half-sinusoidal shock) according to IEC 60068-2-27	20 (half-sinusoidal shock 20 ms) g
Safe isolation to EN 61140 >Between auxiliary contacts and main contacts	500 V AC
Safe isolation to EN 61140 >between the auxiliary contacts	300 V AC
Mounting position	Vertical and 90° in all directions   With XFI earth-fault release: - NZM1, N1, NZM2, N2: vertical and 90° in all directions with plug-in unit - NZM1, N1, NZM2, N2: vertical, 90° right/left with withdrawable unit: - NZM3, N3: vertical, 90° right/left - NZM4, N4: vertical with remote operator: - NZM2, N(S)2, NZM3, N(S)3, NZM4, N(S)4: vertical and 90° in all directions
Direction of incoming supply	as required
Degree of protection >Device	In the operating controls area: IP20 (basic degree of protection)
Degree of protection >Enclosures	With insulating surround: IP40 With door coupling rotary handle: IP66
Degree of protection >Terminations	Tunnel terminal: IP10 Phase isolator and strip terminal: IP00
Other technical data (sheet catalogue)	Temperature dependency, Derating
Rated current = rated uninterrupted current [In = Iu]	80 A
Rated surge voltage invariability [Uimp ] >Main contacts	6000 V
Rated surge voltage invariability [Uimp ] >Auxiliary contacts	6000 V
Rated operational voltage [Ue]	690 V AC
Overvoltage category/pollution degree	III/3
Rated insulation voltage [Ui ]	690 V
Use in unearthed supply systems	≦ 690 V
Rated short-circuit making capacity [Icm ] >240 V [Icm ]	220 kA
Rated short-circuit making capacity [Icm ] >400/415 V [Icm ]	220 kA
Rated short-circuit making capacity [Icm ] >440 V 50/60 Hz [Icm ]	74 kA
Rated short-circuit making capacity [Icm ] >525 V 50/60 Hz [Icm ]	40 kA
Rated short-circuit making capacity [Icm ] >690 V 50/60 H [Ic]	17 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >240 V 50/60 Hz [Icu ]	100 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >400/415 V 50/60 Hz [Icu ]	100 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >440 V 50/60 Hz [Icu ]	70 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >525 V 50/60 Hz [Icu ]	20 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >690 V 50/60 Hz [Icu ]	10 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >240 V 50/60 Hz [Ics ]	100 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >400/415 V 50/60 Hz [Ics ]	50 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >440 V 50/60 Hz [Ics ]	35 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >525 V 50/60 Hz [Ics ]	10 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >690 V 50/60 Hz [Ics]	7.5 kA
Rated short-circuit breaking capacity Icn [Icn ]	Maximum back-up fuse, if the expected short-circuit currents at the installation location exceed the switching capacity of the circuit-breaker.
Utilization category to IEC/EN 60947-2	A
Lifespan, mechanical(of which max. 50 % trip by shunt/undervoltage release) [Operations]	20000
Lifespan, electrical >AC-1 >400 V 50/60 Hz [Operations]	10000
Lifespan, electrical >AC-1 >415 V 50/60 Hz [Operations]	10000
Lifespan, electrical >AC-1 >690 V 50/60 Hz [Operations]	7500
Lifespan, electrical >AC--3 >400 V 50/60 Hz [Operations]	7500
Lifespan, electrical >AC--3 >415 V 50/60 Hz [Operations]	7500
Lifespan, electrical >AC--3 >690 V 50/60 Hz [Operations]	5000
Lifespan, electrical >Max. operating frequency	120 Ops/h
Total break time at short-circuit	< 10 ms
Standard equipment	Box terminal
Accessories required	NZM1-XSVS
Optional accessories	Screw connection Tunnel terminal connection on rear
Round copper conductor >Box terminal >Solid	1 x (10 - 16) 2 x (6 - 16) mm2
Round copper conductor >Box terminal >Stranded	1 x (10 - 70) 3) 2 x (6-25) mm2
Round copper conductor >Box terminal	3) Up to 95 mm² can be connected depending on the cable manufacturer.
Round copper conductor >Tunnel terminal >Solid	1 x 16 mm2
Round copper conductor >Tunnel terminal >Stranded >1-hole	1 x (25 - 95) mm2
Round copper conductor >Bolt terminal and rear-side connection >Direct on the switch >Solid	1 x (10 - 16) 2 x (6 - 16) mm2
Round copper conductor >Bolt terminal and rear-side connection >Direct on the switch >Stranded	1 x (10 - 70) 3) 2 x 25 mm2
Round copper conductor >Bolt terminal and rear-side connection >Direct on the switch	3) Up to 95 mm² can be connected depending on the cable manufacturer.
Al circular conductor >Tunnel terminal >Solid	1 x 16 mm2
Al circular conductor >Tunnel terminal >Stranded >Stranded	1 x (25 - 95) mm2
Al circular conductor >Bolt terminal and rear-side connection >Direct on the switch >Solid	1 x (10 - 16) 2 x (10 - 16) mm2
Al circular conductor >Bolt terminal and rear-side connection >Direct on the switch >Stranded	1 x (25 - 35) 2 x (25 - 35) mm2
Cu strip (number of segments x width x segment thickness) >Box terminal [min.]	2 x 9 x 0.8 mm
Cu strip (number of segments x width x segment thickness) >Box terminal [max.]	9 x 9 x 0.8 mm
Copper busbar (width x thickness) [mm] >Bolt terminal and rear-side connection >Screw connection	M6
Copper busbar (width x thickness) [mm] >Bolt terminal and rear-side connection >Direct on the switch [min.]	12 x 5 mm
Copper busbar (width x thickness) [mm] >Bolt terminal and rear-side connection >Direct on the switch [max.]	16 x 5 mm
Control cables	1 x (0.75 - 2.5) 2 x (0.75 - 1.5) mm2
Rated operational current for specified heat dissipation [In]	80 A
Equipment heat dissipation, current-dependent [Pvid]	16.32 W
Operating ambient temperature min.	-25 °C
Operating ambient temperature max.	+70 °C
10.2 Strength of materials and parts >10.2.2 Corrosion resistance	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.3.1 Verification of thermal stability of enclosures	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.3.2 Verification of resistance of insulating materials to normal heat	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.3.3 Verification of resistance of insulating materials to abnormal heat and fire due to internal electric effects	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.4 Resistance to ultra-violet (UV) radiation	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.5 Lifting	Does not apply, since the entire switchgear needs to be evaluated.
10.2 Strength of materials and parts >10.2.6 Mechanical impact	Does not apply, since the entire switchgear needs to be evaluated.
10.2 Strength of materials and parts >10.2.7 Inscriptions	Meets the product standard´s requirements.
10.3 Degree of protection of ASSEMBLIES	Does not apply, since the entire switchgear needs to be evaluated.
10.4 Clearances and creepage distances	Meets the product standard´s requirements.
10.5 Protection against electric shock	Does not apply, since the entire switchgear needs to be evaluated.
10.6 Incorporation of switching devices and components	Does not apply, since the entire switchgear needs to be evaluated.
10.7 Internal electrical circuits and connections	Is the panel builder´s responsibility.
10.8 Connections for external conductors	Is the panel builder´s responsibility.
10.9 Insulation properties >10.9.2 Power-frequency electric strength	Is the panel builder´s responsibility.
10.9 Insulation properties >10.9.3 Impulse withstand voltage	Is the panel builder´s responsibility.
10.9 Insulation properties >10.9.4 Testing of enclosures made of insulating material	Is the panel builder´s responsibility.
10.10 Temperature rise	The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.
10.11 Short-circuit rating	Is the panel builder´s responsibility. The specifications for the switchgear must be observed.
10.12 Electromagnetic compatibility	Is the panel builder´s responsibility. The specifications for the switchgear must be observed.
10.13 Mechanical function	The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.
Overload release current setting	0 - 0 A
Adjustment range undelayed short-circuit release	8 - 14 A
With thermal protection	No
Phase failure sensitive	No
Switch off technique	Magnetic
Rated operating voltage	690 - 690 V
Rated permanent current Iu	80 A
Rated operation power at AC-3, 230 V	22 kW
Rated operation power at AC-3, 400 V	45 kW
Type of electrical connection of main circuit	Other
Type of control element	Rocker lever
Device construction	Built-in device plug-in technique
With integrated auxiliary switch	No
With integrated under voltage release	No
Number of poles	3
Rated short-circuit breaking capacity lcu at 400 V, AC	100 kA
Degree of protection (IP)	IP20
Height	145 mm
Width	90 mm
Depth	84.5 mm

Mnelko olarak, endüstriyel otomasyon çözümlerinde güvenilir bir iş ortağı olarak, geniş ürün yelpazesi ile işletmenizin tüm ihtiyaçlarını karşılamaya yönelik kaliteli ve yenilikçi ürünler sunmaktayız. Ürün portföyümüz, modern endüstriyel süreçleri desteklemek amacıyla yüksek performans, dayanıklılık ve verimlilik ilkeleri doğrultusunda tasarlanmış çözümlerden oluşur.
Tüm ürünlerimiz, zorlu çalışma koşullarında dahi maksimum güvenilirlik sunar ve işletmenizin operasyonlarını sorunsuz şekilde sürdürmesine yardımcı olur. Endüstriyel otomasyon, enerji yönetimi, kablolama çözümleri ve daha birçok alanda sunduğumuz ürünler, farklı sektörlerdeki ihtiyaçlara esneklikle uyum sağlar.
Ayrıca, ürünlerimiz sadece kaliteli malzemelerle üretilmiş olup, uluslararası standartlara uygunluk göstermektedir. Müşterilerimize sunduğumuz çözümlerle, operasyonel verimliliklerini artırmalarına ve maliyetlerini optimize etmelerine olanak tanıyoruz. Teknolojik gelişmeleri yakından takip eden firmamız, sürekli olarak yenilikçi ürünler sunarak, müşterilerimizin rekabet avantajı elde etmesine destek vermektedir.
Her bir ürün sayfamızda, teknik detaylar, kullanım alanları ve ürün özelliklerine dair kapsamlı bilgilere ulaşabilirsiniz. Endüstriyel süreçlerinizi güçlendirmek için ihtiyacınız olan tüm ürünleri sitemizden keşfedebilir, sorunsuz bir satın alma deneyimi yaşayabilirsiniz.