alt
alt

DILMP45-10(*V60HZ)
109817 DILMP45-10(*V60HZ)
109817

Kontaktör, 4 kutuplu, 45 A, 1 N/O, *V 60 Hz, AC çalışma Kontaktör, Uygulama: 4 kutuplu elektrik tüketicileri için kontaktörler, 200 A'ya kadar kontaktörler, 4 kutuplu, Kullanım kategorisi: AC-1: Endüktif olmayan veya hafif endüktif yükler, dirençli fırınlar, NAC-3: Normal AC endüksiyon motorları: başlatma, anahtarlama çalışma sırasında kapalı, Bağlantı tekniği: Vidalı terminaller, Kutup sayısı: 4 kutuplu, 380 V 400 V: Ie= 25 A, Konvansiyonel serbest hava termal akımı, 3 kutuplu, 50 - 60 Hz 40 °C'de açık: Ith =Ie= 45 A, kapalı: Ith= 36 A, Konvansiyonel serbest hava termal akımı, 1 kutup açık: Ith= 117 A, kapalı: Ith= 105 A, 220 V 230 V: P= 7,5 kW, 380 V 400 V: P= 11 kW, 660 V 690 V: P= 14 kW, Kontaklar N/O = Normalde açık: 1 N/O, Talimatlar: EN 50 012'ye göre kontaklar, Gerilim AC/DC: AC çalışması

Kontaktör, 4 kutuplu, 45 A, 1 N/O, *V 60 Hz, AC çalışma
Kontaktör, Uygulama: 4 kutuplu elektrik tüketicileri için kontaktörler, 200 A'ya kadar kontaktörler, 4 kutuplu, Kullanım kategorisi: AC-1: Endüktif olmayan veya hafif endüktif yükler, dirençli fırınlar, NAC-3: Normal AC endüksiyon motorları: başlatma, anahtarlama çalışma sırasında kapalı, Bağlantı tekniği: Vidalı terminaller, Kutup sayısı: 4 kutuplu, 380 V 400 V: Ie= 25 A, Konvansiyonel serbest hava termal akımı, 3 kutuplu, 50 - 60 Hz 40 °C'de açık: Ith =Ie= 45 A, kapalı: Ith= 36 A, Konvansiyonel serbest hava termal akımı, 1 kutup açık: Ith= 117 A, kapalı: Ith= 105 A, 220 V 230 V: P= 7,5 kW, 380 V 400 V: P= 11 kW, 660 V 690 V: P= 14 kW, Kontaklar N/O = Normalde açık: 1 N/O, Talimatlar: EN 50 012'ye göre kontaklar, Gerilim AC/DC: AC çalışması

Product range Contactors
Application Contactors for 4 pole electric consumers
Subrange Contactors up to 200 A, 4 pole
Utilization category AC-1: Non-inductive or slightly inductive loads, resistance furnaces
NAC-3: Normal AC induction motors: starting, switch off during running
Connection technique Screw terminals
Number of poles 4 pole
AC-1
>Conventional free air thermal current, 3 pole, 50 - 60 Hz
>at 40 °C [Ith =Ie]
AC-1
>Conventional free air thermal current, 3 pole, 50 - 60 Hz
>at 50 °C [Ith =Ie]
45 A
AC-1
>Conventional free air thermal current, 3 pole, 50 - 60 Hz
>at 55 °C [Ith =Ie]
41 A
AC-1
>Conventional free air thermal current, 3 pole, 50 - 60 Hz
>at 60 °C [Ith =Ie]
40 A
N/O = Normally open 39 A
Contact sequence
For use with 1 N/O
Actuating voltage 210S028
Voltage AC/DC DILM32-XHI(C)…
DILA-XHI(V)(C)…
Connection to SmartWire-DT *V 60 Hz
Instructions AC operation
Note on equipment supplied no
Standards Contacts to EN 50 012.
Lifespan, mechanical
>AC operated [Operations]
Minimum order quantity 10 items (packaging unit)
Lifespan, mechanical
>DC operated [Operations]
Operating frequency, mechanical
>AC operated [Operations/h]
IEC/EN 60947, VDE 0660, UL, CSA
Operating frequency, mechanical
>DC operated [Operations/h]
10 x 106
Climatic proofing 10 x 106
Ambient temperature
>Open
5000
Ambient temperature
>Enclosed
5000
Ambient temperature
>Storage
Damp heat, constant, to IEC 60068-2-3
Damp heat, cyclic, to IEC 60068-2-30
Mounting position
>Mounting position
-25 - +60 °C
Mechanical shock resistance (IEC/EN 60068-2-27)
>Half-sinusoidal shock, 10 ms
>Main contacts
>N/O contact
- 25 - 40 °C
Mechanical shock resistance (IEC/EN 60068-2-27)
>Half-sinusoidal shock, 10 ms
>Auxiliary contacts
>N/O contact
- 40 - 80 °C
Mechanical shock resistance (IEC/EN 60068-2-27)
>Half-sinusoidal shock, 10 ms
>Auxiliary contacts
>N/C contact
210N017210N018
Degree of Protection 10 g
Altitude 7 g
Protection against direct contact when actuated from front (EN 50274) 5 g
Stripping length IP00
Terminal capacity main cable
>Solid
Max. 2000 m
Terminal capacity main cable
>Flexible with ferrule
Finger and back-of-hand proof
Terminal capacity main cable
>Stranded
10 mm
Terminal capacity main cable
>Solid or stranded
1 x (0.75 - 16)
2 x (0.75 - 10) mm2
Terminal capacity main cable
>Terminal screw
1 x (0.75 - 16)
2 x (0.75 - 10) mm2
Terminal capacity main cable
>Tightening torque
1 x 16 mm2
Terminal capacity main cable
>Stripping length
18 - 6 AWG
Terminal capacity main cable
>Push-in terminals
>Solid
M5
Terminal capacity main cable
>Push-in terminals
>flexible
3 Nm
Terminal capacity main cable
>Push-in terminals
>flexible with ferrules
10 mm
Terminal capacity main cable
>Push-in terminals
>Solid or stranded
1 x (0.75 - 2.5)
2 x (0.75 - 2.5) mm2
Terminal capacity control circuit cables
>Solid
1 x (0.75 - 2.5)
2 x (0.75 - 2.5) mm2
Terminal capacity control circuit cables
>Flexible with ferrule
1 x (0.75 - 1.5)
2 x (0.75 - 1.5) mm2
Terminal capacity control circuit cables
>Solid or stranded
18 - 14 AWG
Terminal capacity control circuit cables
>Stripping length
1 x (0.75 - 4)
2 x (0.75 - 2.5) mm2
Terminal capacity control circuit cables
>Terminal screw
1 x (0.75 - 2.5)
2 x (0.75 - 2.5) mm2
Terminal capacity control circuit cables
>Tightening torque
18 - 14 AWG
Terminal capacity control circuit cables
>Push-in terminals
>Solid
10 mm
Terminal capacity control circuit cables
>Push-in terminals
>Flexible
M3.5
Terminal capacity control circuit cables
>Push-in terminals
>Flexible with ferrule
1.2 Nm
Terminal capacity control circuit cables
>Push-in terminals
>Solid or stranded
1 x (0.75 - 2.5)
2 x (0.75 - 2.5) mm2
Tool
>Main cable
>Pozidriv screwdriver
1 x (0.75 - 2.5)
2 x (0.75 - 2.5) mm2
Tool
>Main cable
>Standard screwdriver
1 x (0.75 - 1.5)
2 x (0.75 - 1.5) mm2
Tool
>Control circuit cables
>Pozidriv screwdriver
18 - 14 AWG
Tool
>Control circuit cables
>Standard screwdriver
2 Size
Rated impulse withstand voltage [Uimp] 0.8 x 5.5
1 x 6 mm
Overvoltage category/pollution degree 2 Size
Rated insulation voltage [Ui] 0.8 x 5.5
1 x 6 mm
Rated operational voltage [Ue]
Safe isolation to EN 61140
>between coil and contacts
8000 V AC
Safe isolation to EN 61140
>between the contacts
III/3
Making capacity (cos ϕ) [Up to 690 V] 690 V AC
Breaking capacity
>220 V 230 V
690 V AC
Breaking capacity
>380 V 400 V
440 V AC
Breaking capacity
>500 V
440 V AC
Breaking capacity
>660 V 690 V
350
According to IEC/EN 60947 A
Short-circuit rating
>Short-circuit protection maximum fuse
>Type “2” coordination
>400 V [gG/gL 500 V]
250 A
Short-circuit rating
>Short-circuit protection maximum fuse
>Type “2” coordination
>690 V [gG/gL 690 V]
250 A
Short-circuit rating
>Short-circuit protection maximum fuse
>Type “1” coordination
>400 V [gG/gL 500 V]
250 A
Short-circuit rating
>Short-circuit protection maximum fuse
>Type “1” coordination
>690 V [gG/gL 690 V]
144 A
AC-1
>Rated operational current
>Conventional free air thermal current, 3 pole, 50 - 60 Hz
>Open
>at 40 °C [Ith =Ie]
35 A
AC-1
>Rated operational current
>Conventional free air thermal current, 3 pole, 50 - 60 Hz
>Open
>at 50 °C [Ith =Ie]
35 A
AC-1
>Rated operational current
>Conventional free air thermal current, 3 pole, 50 - 60 Hz
>Open
>at 55 °C [Ith =Ie]
100 A
AC-1
>Rated operational current
>Conventional free air thermal current, 3 pole, 50 - 60 Hz
>Open
>at 60 °C [Ith =Ie]
50 A
AC-1
>Rated operational current
>Conventional free air thermal current, 3 pole, 50 - 60 Hz
>enclosed [Ith ]
AC-1
>Rated operational current
>Conventional free air thermal current, 1 pole
>open [Ith ]
45 A
AC-1
>Rated operational current
>Conventional free air thermal current, 1 pole
>enclosed [Ith ]
41 A
AC-1
>Motor rating [P]
>220/230 V [P]
40 A
AC-1
>Motor rating [P]
>240 V [P]
39 A
AC-1
>Motor rating [P]
>380/400 V [P]
36 A
AC-1
>Motor rating [P]
>415 V [P]
117 A
AC-1
>Motor rating [P]
> 440 V [P]
105 A
AC-1
>Motor rating [P]
>500 V [P]
16 kW
AC-1
>Motor rating [P]
>690 V [P]
18 kW
AC-3
>Rated operational current
>Open, 3-pole: 50 – 60 Hz
>Notes
28 kW
AC-3
>Rated operational current
>Open, 3-pole: 50 – 60 Hz
>220 V 230 V [Ie]
31 kW
AC-3
>Rated operational current
>Open, 3-pole: 50 – 60 Hz
>240 V [Ie]
33 kW
AC-3
>Rated operational current
>Open, 3-pole: 50 – 60 Hz
>380 V 400 V [Ie]
37 kW
AC-3
>Rated operational current
>Open, 3-pole: 50 – 60 Hz
>415 V [Ie]
49 kW
AC-3
>Rated operational current
>Open, 3-pole: 50 – 60 Hz
>440V [Ie]
At maximum permissible ambient temperature (open.)
AC-3
>Rated operational current
>Open, 3-pole: 50 – 60 Hz
>500 V [Ie]
25 A
AC-3
>Rated operational current
>Open, 3-pole: 50 – 60 Hz
>660 V 690 V [Ie]
25 A
AC-3
>Motor rating [P]
>220 V 230 V [P]
25 A
AC-3
>Motor rating [P]
>240V [P]
25 A
AC-3
>Motor rating [P]
>380 V 400 V [P]
25 A
AC-3
>Motor rating [P]
>415 V [P]
25 A
AC-3
>Motor rating [P]
>440 V [P]
15 A
AC-3
>Motor rating [P]
>500 V [P]
7.5 kW
AC-3
>Motor rating [P]
>660 V 690 V [P]
8.5 kW
Rated operational current, open
>DC-1
>60 V [Ie ]
11 kW
Rated operational current, open
>DC-1
>110 V [Ie ]
14.5 kW
Rated operational current, open
>DC-1
>220 V [Ie ]
15.5 kW
3 pole, at Ith (60°) 17.5 kW
Impedance per pole 14 kW
Voltage tolerance
>AC operated 50 Hz [Pick-up]
Voltage tolerance
>AC operated 50/60 Hz
45 A
Voltage tolerance
>Drop-out voltage AC operated [Drop-out]
45 A
Power consumption of the coil in a cold state and 1.0 x US
>AC operated 50/60 Hz [Pick-up]
45 A
Power consumption of the coil in a cold state and 1.0 x US
>AC operated 50/60 Hz [Pick-up]
Power consumption of the coil in a cold state and 1.0 x US
>AC operated 50/60 Hz [Sealing]
13.2 W
Power consumption of the coil in a cold state and 1.0 x US
>AC operated 50/60 Hz [Sealing]
2.7 mΩ
Duty factor
Changeover time at 100 % US (recommended value)
>Main contacts
>AC operated
>Closing delay
0.8 - 1.1 x Uc
Changeover time at 100 % US (recommended value)
>Main contacts
>AC operated
>Opening delay
0.85 - 1.1 x Uc
Changeover time at 100 % US (recommended value)
>Permissible residual current with actuation of A1 - A2 by the electronics (with 0 signal).
0.4 - 0.6 x Uc
Switching capacity
>Maximum motor rating
>Three-phase
>200 V
208 V
50 VA
Switching capacity
>Maximum motor rating
>Three-phase
>230 V
240 V
40 W
Switching capacity
>Maximum motor rating
>Three-phase
>460 V
480 V
8 VA
Switching capacity
>Maximum motor rating
>Three-phase
>575 V
600 V
2.1 W
Switching capacity
>Maximum motor rating
>Single-phase
>115 V
120 V
100 % DF
Switching capacity
>Maximum motor rating
>Single-phase
>230 V
240 V
16 - 22 ms
Switching capacity
>General use
8 - 14 ms
Auxiliary contacts
>Pilot Duty
>AC operated
≦ 1 mA
Auxiliary contacts
>Pilot Duty
>DC operated
Auxiliary contacts
>General Use
>AC
7.5 HP
Auxiliary contacts
>General Use
>AC
10 HP
Auxiliary contacts
>General Use
>DC
15 HP
Auxiliary contacts
>General Use
>DC
20 HP
Short Circuit Current Rating
>Basic Rating
>SCCR
2 HP
Short Circuit Current Rating
>Basic Rating
>max. Fuse
5 HP
Short Circuit Current Rating
>Basic Rating
>max. CB
40 A
Short Circuit Current Rating
>480 V High Fault
>SCCR (fuse)
A600
Short Circuit Current Rating
>480 V High Fault
>max. Fuse
P300
Short Circuit Current Rating
>480 V High Fault
>SCCR (CB)
600 V
Short Circuit Current Rating
>480 V High Fault
>max. CB
10 A
Short Circuit Current Rating
>600 V High Fault
>SCCR (fuse)
250 V
Short Circuit Current Rating
>600 V High Fault
>max. Fuse
1 A
Short Circuit Current Rating
>600 V High Fault
>SCCR (CB)
5 kA
Short Circuit Current Rating
>600 V High Fault
>max. CB
125 A
Special Purpose Ratings
>Electrical Discharge Lamps (Ballast)
>480V 60Hz 3phase, 277V 60Hz 1phase
125 A
Special Purpose Ratings
>Electrical Discharge Lamps (Ballast)
>600V 60Hz 3phase, 347V 60Hz 1phase
10/100 kA
Special Purpose Ratings
>Incandescent Lamps (Tungsten)
>480V 60Hz 3phase, 277V 60Hz 1phase
125/70 Class J A
Special Purpose Ratings
>Incandescent Lamps (Tungsten)
>600V 60Hz 3phase, 347V 60Hz 1phase
10/65 kA
Special Purpose Ratings
>Resistance Air Heating
>480V 60Hz 3phase, 277V 60Hz 1phase
50/32 A
Special Purpose Ratings
>Resistance Air Heating
>600V 60Hz 3phase, 347V 60Hz 1phase
10/100 kA
Special Purpose Ratings
>Refrigeration Control (CSA only)
>LRA 480V 60Hz 3phase
125/100 Class J A
Special Purpose Ratings
>Refrigeration Control (CSA only)
>FLA 480V 60Hz 3phase
10/22 kA
Special Purpose Ratings
>Refrigeration Control (CSA only)
>LRA 600V 60Hz 3phase
50/32 A
Special Purpose Ratings
>Refrigeration Control (CSA only)
>FLA 600V 60Hz 3phase
40 A
Special Purpose Ratings
>Definite Purpose Ratings (100,000 cycles acc. to UL 1995)
>LRA 480V 60Hz 3phase
40 A
Special Purpose Ratings
>Definite Purpose Ratings (100,000 cycles acc. to UL 1995)
>FLA 480V 60Hz 3phase
40 A
Special Purpose Ratings
>Elevator Control
>200V 60Hz 3phase
40 A
Special Purpose Ratings
>Elevator Control
>200V 60Hz 3phase
40 A
Special Purpose Ratings
>Elevator Control
>240V 60Hz 3phase
40 A
Special Purpose Ratings
>Elevator Control
>240V 60Hz 3phase
240 A
Special Purpose Ratings
>Elevator Control
>480V 60Hz 3phase
40 A
Special Purpose Ratings
>Elevator Control
>480V 60Hz 3phase
180 A
Special Purpose Ratings
>Elevator Control
>600V 60Hz 3phase
30 A
Special Purpose Ratings
>Elevator Control
>600V 60Hz 3phase
150 A
Rated operational current for specified heat dissipation [In] 25 A
Heat dissipation per pole, current-dependent [Pvid] 3 HP
Equipment heat dissipation, current-dependent [Pvid] 11 A
Static heat dissipation, non-current-dependent [Pvs] 5 HP
Heat dissipation capacity [Pdiss] 15.2 A
Operating ambient temperature min. 10 HP
Operating ambient temperature max. 14 A
10.2 Strength of materials and parts
>10.2.2 Corrosion resistance
15 HP
10.2 Strength of materials and parts
>10.2.3.1 Verification of thermal stability of enclosures
17 A
10.2 Strength of materials and parts
>10.2.3.2 Verification of resistance of insulating materials to normal heat
10.2 Strength of materials and parts
>10.2.3.3 Verification of resistance of insulating materials to abnormal heat and fire due to internal electric effects
45 A
10.2 Strength of materials and parts
>10.2.4 Resistance to ultra-violet (UV) radiation
4.4 W
10.2 Strength of materials and parts
>10.2.5 Lifting
13.2 W
10.2 Strength of materials and parts
>10.2.6 Mechanical impact
2.1 W
10.2 Strength of materials and parts
>10.2.7 Inscriptions
0 W
10.3 Degree of protection of ASSEMBLIES -25 °C
10.4 Clearances and creepage distances +60 °C
10.5 Protection against electric shock
10.6 Incorporation of switching devices and components Meets the product standard´s requirements.
10.7 Internal electrical circuits and connections Meets the product standard´s requirements.
10.8 Connections for external conductors Meets the product standard´s requirements.
10.9 Insulation properties
>10.9.2 Power-frequency electric strength
Meets the product standard´s requirements.
10.9 Insulation properties
>10.9.3 Impulse withstand voltage
Meets the product standard´s requirements.
10.9 Insulation properties
>10.9.4 Testing of enclosures made of insulating material
Does not apply, since the entire switchgear needs to be evaluated.
10.10 Temperature rise Does not apply, since the entire switchgear needs to be evaluated.
10.11 Short-circuit rating Meets the product standard´s requirements.
10.12 Electromagnetic compatibility Does not apply, since the entire switchgear needs to be evaluated.
10.13 Mechanical function Meets the product standard´s requirements.
Rated control supply voltage Us at AC 50HZ Does not apply, since the entire switchgear needs to be evaluated.
Rated control supply voltage Us at AC 60HZ Does not apply, since the entire switchgear needs to be evaluated.
Rated control supply voltage Us at DC Is the panel builder´s responsibility.
Voltage type for actuating Is the panel builder´s responsibility.
Rated operation current Ie at AC-1, 400 V Is the panel builder´s responsibility.
Rated operation current Ie at AC-3, 400 V Is the panel builder´s responsibility.
Rated operation power at AC-3, 400 V Is the panel builder´s responsibility.
Rated operation current Ie at AC-4, 400 V The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.
Rated operation power at AC-4, 400 V Is the panel builder´s responsibility. The specifications for the switchgear must be observed.
Rated operation power NEMA Is the panel builder´s responsibility. The specifications for the switchgear must be observed.
Modular version The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.
Number of auxiliary contacts as normally open contact
Number of auxiliary contacts as normally closed contact
Type of electrical connection of main circuit 0 - 0 V
Number of normally closed contacts as main contact 24 - 600 V
Number of main contacts as normally open contact 0 - 0 V
Product Standards AC
UL File No. 45 A
UL Category Control No. 25 A
CSA File No. 11 kW
CSA Class No. 15 A
North America Certification 7 kW
Specially designed for North America 11 kW
Accessories No
Characteristic curve 1

Mnelko olarak, endüstriyel otomasyon çözümlerinde güvenilir bir iş ortağı olarak, geniş ürün yelpazesi ile işletmenizin tüm ihtiyaçlarını karşılamaya yönelik kaliteli ve yenilikçi ürünler sunmaktayız. Ürün portföyümüz, modern endüstriyel süreçleri desteklemek amacıyla yüksek performans, dayanıklılık ve verimlilik ilkeleri doğrultusunda tasarlanmış çözümlerden oluşur.
Tüm ürünlerimiz, zorlu çalışma koşullarında dahi maksimum güvenilirlik sunar ve işletmenizin operasyonlarını sorunsuz şekilde sürdürmesine yardımcı olur. Endüstriyel otomasyon, enerji yönetimi, kablolama çözümleri ve daha birçok alanda sunduğumuz ürünler, farklı sektörlerdeki ihtiyaçlara esneklikle uyum sağlar.
Ayrıca, ürünlerimiz sadece kaliteli malzemelerle üretilmiş olup, uluslararası standartlara uygunluk göstermektedir. Müşterilerimize sunduğumuz çözümlerle, operasyonel verimliliklerini artırmalarına ve maliyetlerini optimize etmelerine olanak tanıyoruz. Teknolojik gelişmeleri yakından takip eden firmamız, sürekli olarak yenilikçi ürünler sunarak, müşterilerimizin rekabet avantajı elde etmesine destek vermektedir.
Her bir ürün sayfamızda, teknik detaylar, kullanım alanları ve ürün özelliklerine dair kapsamlı bilgilere ulaşabilirsiniz. Endüstriyel süreçlerinizi güçlendirmek için ihtiyacınız olan tüm ürünleri sitemizden keşfedebilir, sorunsuz bir satın alma deneyimi yaşayabilirsiniz.

Benzer Ürünler

DILMC80(RDC24)
Eaton
DILMC95(230V50HZ,240V60HZ)
Eaton
DILMC95(RDC24)
Eaton
DILMC115(RAC240)
Eaton
DILMC115(RDC24)
Eaton
DILMC150(RAC240)
Eaton
DILMC150(RDC24)
Eaton
SDAINLM70(230V50HZ,240V60HZ)
Eaton
SDAINLM90(230V50HZ,240V60HZ)
Eaton