DILH2000/22(RAW250)
272442 DILH2000/22(RAW250)
272442

Kontaktör, Ith =Ie: 2450 A, RAW 250: 230 - 250 V 50 - 60 Hz/230 - 350 V DC, AC ve DC çalışma, Vidalı bağlantı
Kontaktör, Uygulama: 1000 A'den itibaren dirençli yükler için şebeke kontaktörleri, 1000 A'dan büyük AC -1 kontaktörler, Kullanım kategorisi: AC-1: Endüktif olmayan veya hafif endüktif yükler, direnç fırınları, Bağlantı tekniği: Vidalı bağlantı, Nominal çalışma akımı AC -1 Konvansiyonel serbest hava termik akımı, 3 kutuplu, 50 - 60 Hz 40 °C'de açık: Ith =Ie= 2450 A, Nominal çalışma akımı AC-1 Konvansiyonel serbest hava termik akımı, 1 kutup açık: Ith= 5000 A, For Şunlarla kullanın: DILM820-XHI…, Talimatlar: Çalıştırma elektroniğinde entegre baskılayıcı devre, 660 V, 690 V veya 1000 V: doğrudan yön değiştirmeyen, Gerilim AC/DC: AC ve DC çalışması

Product range	Contactors
Application	Mains contactors for resistive loads from 1000 A
Subrange	AC -1 contactors greater than 1000 A
Utilization category	AC-1: Non-inductive or slightly inductive loads, resistance furnaces
Connection technique	Screw connection
AC-1 >Conventional free air thermal current, 3 pole, 50 - 60 Hz >Open >at 40 °C [Ith =Ie]
AC-1 >Conventional free air thermal current, 1 pole >open [Ith ]	2450 A
Contact sequence	5000 A
For use with
Actuating voltage	DILM820-XHI…
Voltage AC/DC	RAW 250: 230 - 250 V 50 - 60 Hz/230 - 350 V DC
possible variants at auxiliary contact module fitting options	AC and DC operation
Side mounting auxiliary contacts
Instructions	on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA
Instructions
Note concerning the product	Interlocked opposing contacts according to IEC/EN 60947-5-1 Appendix L, inside the auxiliary contact module Auxiliary contacts used as mirror contacts according to IEC/EN 60947-4-1 Appendix F (not N/C late open)
Standards	integrated suppressor circuit in actuating electronics 660 V, 690 V or 1000 V: not directly reversing
Lifespan, mechanical >AC operated [Operations]	Classic   DILM1600, DILH2000, DILH2200   A1/A2 werden wie bisher gewohnt an Spannung gelegt     Direct from the PLC       An die Anschlüsse A3/A4 kann direkt ein 24-V-Ausgang der SPS angeschlossen werden.     From a low-power actuating device   Gering belastbare Befehlsgeber wie Leiterplattenrelais, Befehlsgeräte oder Positionsschalter können direkt an A10/A11 angeschlossen werden.         ① Stopping in the event of an emergency (emergency switching off) ② max. Cable capacitance 6 nF
Lifespan, mechanical >DC operated [Operations]
Operating frequency, mechanical >AC operated [Operations/h]	IEC/EN 60947, VDE 0660, UL, CSA, CCC
Operating frequency, mechanical >DC operated [Operations/h]	5 x 106
Climatic proofing	5 x 106
Ambient temperature >Open	1000
Ambient temperature >Storage	1000
Mounting position	Damp heat, constant, to IEC 60068-2-78 Damp heat, cyclic, to IEC 60068-2-30
Mechanical shock resistance (IEC/EN 60068-2-27) >Half-sinusoidal shock, 10 ms >Main contacts >N/O contact	-40 - +60 °C
Mechanical shock resistance (IEC/EN 60068-2-27) >Half-sinusoidal shock, 10 ms >Auxiliary contacts >N/O contact	- 40 - + 80 °C
Mechanical shock resistance (IEC/EN 60068-2-27) >Half-sinusoidal shock, 10 ms >Auxiliary contacts >N/C contact
Degree of Protection	10 g
Altitude	10 g
Weight	8 g
Terminal capacity main cable >Busbar [Width]	IP00
Main cable connection screw/bolt	Max. 2000 m
Tightening torque	32 kg
Terminal capacity control circuit cables >Solid	100 mm
Terminal capacity control circuit cables >Flexible with ferrule	M12
Terminal capacity control circuit cables >Solid or stranded	35 Nm
Stripping length	1 x (0.75 - 2.5) 2 x (0.75 - 2.5) mm2
Control circuit cable connection screw/bolt	1 x (0.75 - 2.5) 2 x (0.75 - 2.5) mm2
Tightening torque	18 - 14 AWG
Tool >Main cable >Width across flats	10 mm
Tool >Control circuit cables >Pozidriv screwdriver	M3.5
Tool >Control circuit cables >Standard screwdriver	1.2 Nm
Rated impulse withstand voltage [Uimp]	18 mm
Overvoltage category/pollution degree	2 Size
Rated insulation voltage [Ui]	0.8 x 5.5/1 x 6 mm
Rated operational voltage [Ue]
Safe isolation to EN 61140 >between coil and contacts	8000 V AC
Safe isolation to EN 61140 >between the contacts	III/3
Making capacity (p.f. to IEC/EN 60947)	1000 V AC
Breaking capacity >220 V 230 V	1000 V AC
Breaking capacity >380 V 400 V	500 V AC
Breaking capacity >500 V	500 V AC
Breaking capacity >660 V 690 V	9840 A
Breaking capacity >1000 V	8200 A
Component lifespan	8200 A
AC-1 >Rated operational current >Conventional free air thermal current, 3 pole, 50 - 60 Hz >Open >at 40 °C [Ith =Ie]	8200 A
AC-1 >Rated operational current >Conventional free air thermal current, 3 pole, 50 - 60 Hz >Open >at 50 °C [Ith =Ie]	8200 A
AC-1 >Rated operational current >Conventional free air thermal current, 3 pole, 50 - 60 Hz >Open >at 55 °C [Ith =Ie]	5800 A
AC-1 >Rated operational current >Conventional free air thermal current, 3 pole, 50 - 60 Hz >Open >at 60 °C [Ith =Ie]	AC1: See → Engineering, characteristic curves
AC-1 >Rated operational current >Conventional free air thermal current, 1 pole >Note
AC-1 >Rated operational current >Conventional free air thermal current, 1 pole >open [Ith ]	2450 A
3 pole, at Ith (60°)	2190 A
Current heat loss at Ie to AC-3/400 V	2089 A
Voltage tolerance >US	2000 A
Voltage tolerance >AC operated [Pick-up]	at maximum permissible ambient air temperature
Voltage tolerance >DC operated [Pick-up]	5000 A
Voltage tolerance >AC operated [Drop-out]
Voltage tolerance >DC operated [Drop-out]	192 W
Power consumption of the coil in a cold state and 1.0 x US >Note on power consumption	0.016 W
Power consumption of the coil in a cold state and 1.0 x US >Pull-in power [Pick-up]
Power consumption of the coil in a cold state and 1.0 x US >Pull-in power [Pick-up]	230 - 250 V 50/60 Hz 230 - 350 V DC
Power consumption of the coil in a cold state and 1.0 x US >Sealing power [Sealing]	0.7 x US min - 1.15 x US max
Power consumption of the coil in a cold state and 1.0 x US >Sealing power [Sealing]	0.7 x US min - 1.15 x US max
Duty factor	0.2 x US max - 0.6 x US min
Changeover time at 100 % US (recommended value) >Main contacts >Closing delay	0.2 x US max - 0.6 x US min
Changeover time at 100 % US (recommended value) >Main contacts >Opening delay	Control transformer with uk ≦ 7%
Behaviour in marginal and transitional conditions >Sealing >Voltage interruptions >(0 … 0.2 x Uc min) ≦ 10 ms	1600 VA
Behaviour in marginal and transitional conditions >Sealing >Voltage interruptions >(0 … 0.2 x Uc min) > 10 ms	1400 W
Behaviour in marginal and transitional conditions >Sealing >Voltage drops >(0.2 … 0.6 x Uc min) ≦ 12 ms	36.5 VA
Behaviour in marginal and transitional conditions >Sealing >Voltage drops >(0.2 … 0.6 x Uc min) > 12 ms	17.3 W
Behaviour in marginal and transitional conditions >Sealing >Voltage drops >(0.6 … 0.7 x Uc min)	100 % DF
Behaviour in marginal and transitional conditions >Sealing >Excess voltage >(1.15 … 1.3 x Uc max)	70 ms
Behaviour in marginal and transitional conditions >Sealing >Pick-up phase >(0 … 0.7 x Uc min)	40 ms
Behaviour in marginal and transitional conditions >Sealing >Pick-up phase >(0.7 x Uc min … 1.15 x Uc max)	Time is bridged successfully
Admissible transitional contact resistance (of the external control circuit device when actuating A11)	Drop-out of the contactor
PLC signal level (A3 - A4) to IEC/EN 61131-2 (type 2) >High	Time is bridged successfully
PLC signal level (A3 - A4) to IEC/EN 61131-2 (type 2) >Low	Drop-out of the contactor
Electromagnetic compatibility	Contactor remains switched on
Switching capacity >General use	Contactor remains switched on
Auxiliary contacts >Pilot Duty >AC operated	Contactor does not switch on
Auxiliary contacts >Pilot Duty >DC operated	Contactor switches on with certainty
Auxiliary contacts >General Use >AC	≦ 500 mΩ
Auxiliary contacts >General Use >AC	15 V
Auxiliary contacts >General Use >DC	5 V
Auxiliary contacts >General Use >DC
Special Purpose Ratings >Resistance Air Heating >480V 60Hz 3phase, 277V 60Hz 1phase	This product is designed for operation in industrial environments (environment A). Its use in residential environments (environment B) may cause radio-frequency interference, requiring additional noise suppression measures.
Special Purpose Ratings >Resistance Air Heating >600V 60Hz 3phase, 347V 60Hz 1phase
Rated operational current for specified heat dissipation [In]	2000 A
Heat dissipation per pole, current-dependent [Pvid]	A600
Equipment heat dissipation, current-dependent [Pvid]	P300
Static heat dissipation, non-current-dependent [Pvs]	600 V
Heat dissipation capacity [Pdiss]	15 A
Operating ambient temperature min.	250 V
Operating ambient temperature max.	1 A
10.2 Strength of materials and parts >10.2.2 Corrosion resistance	2000 A
10.2 Strength of materials and parts >10.2.3.1 Verification of thermal stability of enclosures	2000 A
10.2 Strength of materials and parts >10.2.3.2 Verification of resistance of insulating materials to normal heat
10.2 Strength of materials and parts >10.2.3.3 Verification of resistance of insulating materials to abnormal heat and fire due to internal electric effects	2000 A
10.2 Strength of materials and parts >10.2.4 Resistance to ultra-violet (UV) radiation	64 W
10.2 Strength of materials and parts >10.2.5 Lifting	0 W
10.2 Strength of materials and parts >10.2.6 Mechanical impact	13 W
10.2 Strength of materials and parts >10.2.7 Inscriptions	0 W
10.3 Degree of protection of ASSEMBLIES	-40 °C
10.4 Clearances and creepage distances	+60 °C
10.5 Protection against electric shock
10.6 Incorporation of switching devices and components	Meets the product standard´s requirements.
10.7 Internal electrical circuits and connections	Meets the product standard´s requirements.
10.8 Connections for external conductors	Meets the product standard´s requirements.
10.9 Insulation properties >10.9.2 Power-frequency electric strength	Meets the product standard´s requirements.
10.9 Insulation properties >10.9.3 Impulse withstand voltage	Meets the product standard´s requirements.
10.9 Insulation properties >10.9.4 Testing of enclosures made of insulating material	Does not apply, since the entire switchgear needs to be evaluated.
10.10 Temperature rise	Does not apply, since the entire switchgear needs to be evaluated.
10.11 Short-circuit rating	Meets the product standard´s requirements.
10.12 Electromagnetic compatibility	Does not apply, since the entire switchgear needs to be evaluated.
10.13 Mechanical function	Meets the product standard´s requirements.
Rated control supply voltage Us at AC 50HZ	Does not apply, since the entire switchgear needs to be evaluated.
Rated control supply voltage Us at AC 60HZ	Does not apply, since the entire switchgear needs to be evaluated.
Rated control supply voltage Us at DC	Is the panel builder´s responsibility.
Voltage type for actuating	Is the panel builder´s responsibility.
Rated operation current Ie at AC-1, 400 V	Is the panel builder´s responsibility.
Rated operation current Ie at AC-3, 400 V	Is the panel builder´s responsibility.
Rated operation power at AC-3, 400 V	Is the panel builder´s responsibility.
Rated operation current Ie at AC-4, 400 V	The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.
Rated operation power at AC-4, 400 V	Is the panel builder´s responsibility. The specifications for the switchgear must be observed.
Rated operation power NEMA	Is the panel builder´s responsibility. The specifications for the switchgear must be observed.
Modular version	The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.
Number of auxiliary contacts as normally open contact
Number of auxiliary contacts as normally closed contact
Type of electrical connection of main circuit	230 - 250 V
Number of normally closed contacts as main contact	230 - 250 V
Number of main contacts as normally open contact	230 - 250 V
Product Standards	AC/DC
UL File No.	2450 A
UL Category Control No.	0 A
CSA File No.	0 kW
CSA Class No.	0 A
North America Certification	0 kW
Specially designed for North America	0 kW
Side mounting auxiliary contacts	No
possible variants at auxiliary contact module fitting options	2
Characteristic curve	2
Characteristic curve	Rail connection

Mnelko olarak, endüstriyel otomasyon çözümlerinde güvenilir bir iş ortağı olarak, geniş ürün yelpazesi ile işletmenizin tüm ihtiyaçlarını karşılamaya yönelik kaliteli ve yenilikçi ürünler sunmaktayız. Ürün portföyümüz, modern endüstriyel süreçleri desteklemek amacıyla yüksek performans, dayanıklılık ve verimlilik ilkeleri doğrultusunda tasarlanmış çözümlerden oluşur.
Tüm ürünlerimiz, zorlu çalışma koşullarında dahi maksimum güvenilirlik sunar ve işletmenizin operasyonlarını sorunsuz şekilde sürdürmesine yardımcı olur. Endüstriyel otomasyon, enerji yönetimi, kablolama çözümleri ve daha birçok alanda sunduğumuz ürünler, farklı sektörlerdeki ihtiyaçlara esneklikle uyum sağlar.
Ayrıca, ürünlerimiz sadece kaliteli malzemelerle üretilmiş olup, uluslararası standartlara uygunluk göstermektedir. Müşterilerimize sunduğumuz çözümlerle, operasyonel verimliliklerini artırmalarına ve maliyetlerini optimize etmelerine olanak tanıyoruz. Teknolojik gelişmeleri yakından takip eden firmamız, sürekli olarak yenilikçi ürünler sunarak, müşterilerimizin rekabet avantajı elde etmesine destek vermektedir.
Her bir ürün sayfamızda, teknik detaylar, kullanım alanları ve ürün özelliklerine dair kapsamlı bilgilere ulaşabilirsiniz. Endüstriyel süreçlerinizi güçlendirmek için ihtiyacınız olan tüm ürünleri sitemizden keşfedebilir, sorunsuz bir satın alma deneyimi yaşayabilirsiniz.