2-channel analog input; 4 … 20 mA HART; Intrinsically safe; blueThe analog input module connects two field-side transformers equipped with a HART interface to be used in hazardous environments Zone 0 + 1. It powers transducers, reads process values via the analog interface, and provides HART communication to configure and import dynamic variables. The WAGO-I/O-SYSTEM 750 must be installed in Zone 2 or a non-hazardous area. The 24V supply is taken from the power bridge contacts via multiplexers to the field contacts (HART +). The shield (screen) is attached directly to the DIN rail. Measurement input, current max. It is equipped with a current limiter that limits it to 25 mA. These modules can supply voltage to 2-wire transducers that do not have a dedicated power supply. Up to 4 HART dynamic variables (PV, SV, TV, QV) per channel can be mapped in the cyclic process image. The HART protocol for HART communication with connected smart HART field devices can be mapped (set) in the cyclic process image of the coupler or controller. FDT/DTM device drivers are available for certain (programmable) couplers and provide HART tool routing to the connected HART device. Note:Note: The analog input module must only be operated via the Ex i 24VDC power supply! General information on explosion protection (e.g. mounting regulations) is available in the WAGO-I/O-SYSTEM 750 manuals!
2-channel analog input; 4 … 20 mA HART; Intrinsically safe; blue
The analog input module connects two field-side transformers equipped with a HART interface to be used in hazardous environments Zone 0 + 1.
It powers transducers, reads process values via the analog interface, and provides HART communication to configure and import dynamic variables.
The WAGO-I/O-SYSTEM 750 must be installed in Zone 2 or a non-hazardous area.
The 24V supply is taken from the power bridge contacts via multiplexers to the field contacts (HART +). The shield (screen) is attached directly to the DIN rail.
Measurement input, current max. It is equipped with a current limiter that limits it to 25 mA. These modules can supply voltage to 2-wire transducers that do not have a dedicated power supply.
Up to 4 HART dynamic variables (PV, SV, TV, QV) per channel can be mapped in the cyclic process image. The HART protocol for HART communication with connected smart HART field devices can be mapped (set) in the cyclic process image of the coupler or controller.
FDT/DTM device drivers are available for certain (programmable) couplers and provide HART tool routing to the connected HART device.
Note: The analog input module must only be operated via the Ex i 24VDC power supply!
General information on explosion protection (e.g. mounting regulations) is available in the WAGO-I/O-SYSTEM 750 manuals!
| Number of analog inputs | 2 |
| Total number of channels (module) | 2 |
| Sinyal tipi | Current |
| Type of signal current | DC 4 … 20 mA |
| Sensor supply voltage | DC 16,5 V; Transmitter supply UV at 20 mA |
| Sensor connection | 2 x (2-conductor) |
| Giriş filtresi | Parametreleştirilebilir |
| Giriş filtresi: parametrelerle ayarlanabilir (kanal-kanal) | yes |
| Signal characteristic | Single-ended |
| Arıza teşhisi | Kablo kopması, ölçüm aralığı dışında |
| Çözünürlük [bit] | 12Bit |
| Güç tüketimi Pmax. | 1,60 W (slave´lerle (20 mA)) |
| Bit genişliği | 2 x 2 byte veri 2 x 2 byte veri + 2n x 4 byte veri (n = dinamik değişken adedi) 2 x 2 byte veri + 6 byte posta kutusu |
| Aşırı gerilim koruması | 30 V, ters polarite korumalı |
| Çevirme süresi (tip.) | 10ms |
| Messfehler, Bezugstemperatur | 25°C |
| Messfehler, Abweichung max. vom Messbereichsendwert | 0,2% |
| Temperaturfehler max. vom Messbereichsendwert | 0,01%/K |
| Kendinden güvenli Ex i | yes |
| System supply voltage | DC 5 V; via data contacts |
| Current consumption, system supply (5 V) | 25mA |
| Field supply voltage | DC 24 V; (Versorgung über Einspeisung Ex i UO = max. 27,3 V); über Leistungskontakte (Einspeisung über Messerkontakt; Weiterleitung über Federkontakt) |
| Current consumption, field supply (module with no external load) | 26mA |
| Kanal başına HART aygıtları | 1 aygıt (single-drop, no multi-drop) |
| Kanal başına HART modemleri | 1 modem (multiplex değil) |
| Güç kaybı PV | 0,62 W (slave´siz) |
| İzolasyon | 300 VAC system/field |
| Number of incoming power jumper contacts | 2 |
| Number of outgoing power jumper contacts | 2 |
| Current carrying capacity of the power jumper contacts | 1A |
| ATEX Guideline | EN/IEC 60079-0, -7, -11, -26, -31 |
| Elektrik şebekesi, güvenliğe ilişkin bilgi | Uo = 27.3 V; Io = 92.7 mA; Po = 630 mW; Characteristic: Linear |
| Reaktans Ex ia IIC | Lo = 1.5 mH; Co = 87 nF |
| Reaktans Ex ia IIB | Lo = 15 mH; Co = 670 nF |
| Reaktans Ex ia IIA | Lo = 38 mH; Co = 2.2 μF |
| Reaktans Ex ia I | Lo = 36 mH; Co = 3.49 µF |
| Reaktans | (The above-listed ratings do not account for the coincidental occurrence of capacitances and inductances. For ratings taking the coincidental occurrence of capacitances and inductances into account, see manual) |
| Etiketleme | ATEX, IECEx, INMETRO, Underwriters Laboratories Inc. |
| Connection technology: In-/Outputs | 16 x CAGE CLAMP® |
| Connection type (1) | Inputs/Outputs |
| Tek damarlı boylar | 0,08 … 2,5 mm² / 28 … 14 AWG |
| İnce bükümlü kablolar | 0,08 … 2,5 mm² / 28 … 14 AWG |
| Sıyırma uzunluğu | 8 … 9 mm / 0.31 … 0.35 inch |
| Width | 24 mm / 0.945 inch |
| Height | 67,8 mm / 2.669 inch |
| DIN rayın üst kenarından yükseklik | 60,6 mm / 2.386 inch |
| Depth | 100 mm / 3.937 inch |
| Montaj tipi | DIN 35 ray |
| Renk | mavi |
| Gövde malzemesi | Polycarbonate, polyamide 6.6 |
| Ağırlık | 92 |
| Uygunluk işareti | CE |
| Surrounding air (operating) temperature | 0 … 55 °C |
| Surrounding air (storage) temperature | -40 … 85 °C |
| Koruma sınıfı | IP20 |
| Kirlilik derecesi (5) | 2 per IEC 61131-2 |
| Çalışma yüksekliği | 0 … 2000 m |
| Montaj pozisyonu | horizontal (standing/lying) or vertical |
| Nısbi nem (yoğuşmasız) | 95% |
| Titreşime dayanıklı | 4g per IEC 60068-2-6 |
| Darbe direnci | 15g per IEC 60068-2-27 |
| EMV-Störfestigkeit | acc. to EN 61000-6-2, marine applications |
| EMU: |
acc. to EN 61000-6-3, marine applications |
| Kirletici maddelere maruziyet | Per IEC 60068-2-42 and IEC 60068-2-43 |
| Permissible H2S contaminant concentration at a relative humidity |
10ppm |
| Permissible SO2 contaminant concentration at a relative humidity |
25ppm |
| Product Group | 15 (Remote I/O) |
| SAP´den ambalaj tipi | BOX |
| Country of origin | DE |
| GTIN | 4017332317603 |
| Customs Tariff No. | 85389099990 |
As Mnelko, we are a reliable partner in industrial automation solutions, offering high-quality and innovative products with a wide product range to meet all the needs of your business. Our product portfolio consists of solutions designed based on the principles of high performance, durability, and efficiency to support modern industrial processes.
All of our products ensure maximum reliability even in challenging working conditions and help your business operations run smoothly. The products we offer in industrial automation, energy management, cabling solutions, and many other areas adapt flexibly to the needs of different sectors.
Additionally, our products are manufactured using only high-quality materials and comply with international standards. Through the solutions we provide, we enable our customers to increase operational efficiency and optimize costs. Our company closely follows technological advancements and continuously offers innovative products to help our customers gain a competitive advantage.
On each of our product pages, you can find comprehensive information about technical details, areas of use, and product features. You can explore all the products you need to strengthen your industrial processes on our website and enjoy a seamless purchasing experience.
All rights reserved. Mnelko Endüstriyel San. ve Tic.Ltd.Şti. 2024
