Actuator monitoredPower to lockSolenoid interlockIntegrated AS-InterfaceThermoplastic enclosure90 mm x 84 mm x 30 mmDouble-insulatedHigh holding force
| Product type description | AZM 170 B ST-AS RAP |
| Article number (order number) | 101210414 |
| EAN (European Article Number) | 4030661390406 |
| eCl@ss number, version 12.0 | 27-27-26-03 |
| eCl@ss number, version 11.0 | 27-27-26-03 |
| eCl@ss number, version 9.0 | 27-27-26-03 |
| ETIM number, version 7.0 | EC002593 |
| ETIM number, version 6.0 | EC002593 |
| IFA cULus ASi-SaW |
| Standards | EN IEC 62026-2 EN ISO 13849-1 EN IEC 60947-5-1 EN IEC 61508 |
| Working principle | electromechanical |
| Housing material | Plastic, glass-fibre reinforced thermoplastic, self-extinguishing |
| Reaction time, maximum | 100 ms |
| Gross weight | 310 g |
| Power to lock | Yes |
| Actuator monitored | Yes |
| Integral system diagnostics, status | Yes |
| Number of actuating directions | 2 |
| Safety classification |
| Standards | EN IEC 61508 |
| Performance Level, up to | c |
| Category | 1 |
| PFH value | 1.16 x 10⁻⁶ /h |
| Note (PFH-value) | up to max. 100,000 switching cycles/year |
| Safety Integrity Level (SIL), suitable for applications in | 1 |
| Mission time | 20 Year(s) |
| Safety classification - Fault exclusion |
| Please note: | Can be used when fault exclusion for dangerous damage to the 1-channel mechanism is permissible and sufficient protection against manipulation is guaranteed. |
| Performance Level, up to | d |
| Category | 3 |
| PFH value | 1.01 x 10⁻⁷ /h |
| Note (PFH-value) | up to max. 100,000 switching cycles/year |
| Safety Integrity Level (SIL), suitable for applications in | 2 |
| Mission time | 20 Year(s) |
| Mechanical life, minimum | 1,000,000 Operations |
| Holding force | 1,000 N |
| Latching force | 30 N |
| Actuating speed, maximum | 2 m/s |
| Termination | Connector plug M12, 4-pole, (A-coding) |
| Width of sensor | 90 mm |
| Height of sensor | 75.5 mm |
| Degree of protection | IP67 |
| Ambient temperature | -25 ... +55 °C |
| Storage and transport temperature | -25 ... +85 °C |
| Relative humidity, minimum | 30 % |
| Relative humidity, maximum | 95 % |
| Note (Relative humidity) | non-condensing non-icing |
| Protection class | II |
| Rated insulation voltage Ui | 32 VDC |
| Rated impulse withstand voltage Uimp | 0.8 kV |
| Overvoltage category | III |
| Degree of pollution | 3 |
| Rated operating voltage | 26.5 ... 31.6 VDC (Protection against polarity reversal) |
| AS-i Current consumption, maximum | 100 mA |
| AS-i Specification | Safety-Slave |
| AS-i Version | V 2.1 |
| AS-i Profile | S-7.B.F.E |
| AS-i, IO-Code | 0x7 |
| AS-i, ID-Code | 0xB |
| AS-i, ID-Code1 | 0xF |
| AS-i, ID-Code2 | 0xE |
| AS-i Input, Channel 1 | Data bits DI 0 / DI 1 = dynamic code transmission |
| AS-i Input, Channel 2 | Data bits DI 2 / DI 3 = dynamic code transmission |
| AS-i Outputs, DO 0 | Solenoid control |
| AS-i Outputs, DO 1 | No Function |
| AS-i Outputs, DO 2 | No Function |
| AS-i Outputs, DO 3 | No Function |
| AS-i Parameter bits, P0 | Safety guard and actuator detected |
| AS-i Parameter bits, P1 | Solenoid interlock locked |
| AS-i Parameter bits, P2 | No function |
| AS-i Parameter bits, P3 | No function |
| Note (AS-i Parameter bits) | Set the parameter outputs to "1111" (0xF) FID: periphery error |
| AS-i Input module address | 0 |
| Note (AS-i Input module address) | Preset to address 0, can be changed through AS-interface bus master or hand-held programming device |
| Operating voltage | 24 VDC -15 % / +10 % (stabilised PELV power supply) |
| Current consumption | 500 mA |
| Rated operating voltage | 24 VDC |
| Note (LED switching conditions display) | (1) LED green: Supply voltage (2) red LED: Communication error / Slave address = 0 (3) LED yellow : Enabling status |
| PIN 1 | AS-i + |
| PIN 2 | Aux - (P) |
| PIN 3 | AS-Interface - |
| PIN 4 | Aux + (P) |
| Scope of delivery | Actuator must be ordered separately. |
| Note (General) | Interlocks with the power to lock principle may only be used in special cases after a thorough evaluation of the accident risk, since the guarding device can immediately be opened on failure of the electrical power supply or when the main switch is opened. |
| Note voltage AUX DC | stabilised PELV power supply |
As Mnelko, we are a reliable partner in industrial automation solutions, offering high-quality and innovative products with a wide product range to meet all the needs of your business. Our product portfolio consists of solutions designed based on the principles of high performance, durability, and efficiency to support modern industrial processes.
All of our products ensure maximum reliability even in challenging working conditions and help your business operations run smoothly. The products we offer in industrial automation, energy management, cabling solutions, and many other areas adapt flexibly to the needs of different sectors.
Additionally, our products are manufactured using only high-quality materials and comply with international standards. Through the solutions we provide, we enable our customers to increase operational efficiency and optimize costs. Our company closely follows technological advancements and continuously offers innovative products to help our customers gain a competitive advantage.
On each of our product pages, you can find comprehensive information about technical details, areas of use, and product features. You can explore all the products you need to strengthen your industrial processes on our website and enjoy a seamless purchasing experience.
All rights reserved. Mnelko Endüstriyel San. ve Tic.Ltd.Şti. 2024
