NZMN3-4-VE400-T-AVE
119902 NZMN3-4-VE400-T-AVE
119902

Circuit-breaker, 4p, 400A, withdrawable unit
Circuit-breaker NZM3, 4 pole, Switching capacity 400/415 V 50 Hz( Icu ): 50 kA, Rated current = rated uninterrupted current Rated current = rated uninterrupted current( In = Iu ): 400 A, Installation type: Withdrawable, Screw connection, Standard/Approval: IEC, Protective function: Systems, cable, selectivity and generator protection

Product range	Circuit-breaker
Protective function	Systems, cable, selectivity and generator protection Earth-fault protection
Standard/Approval	IEC
Installation type	Withdrawable
Release system	Electronic release
Construction size	NZM3
Description	R.m.s. value measurement and “thermal memory” adjustable time delay setting to overcome current peaks tr: 2 – 14 s at 6 x Ir also infinity (without overload releases) Adjustable delay time tsd: Steps: 0, 20, 60, 100, 200, 300, 500, 750, 1000 ms i2t constant function: switchable Earth-fault release: Not dependent on mains and control voltages Ig = 0.35 - 0.4 - 0.5 - 0.6 - 0.7 - 0.8 - 0.9 - 1.0 x In tg = 0 - 20 - 60 - 100 - 200 - 300 - 500 - 750 - 1000 ms
Number of poles	4 pole
Standard equipment	Screw connection
400/415 V 50 Hz [Icu ]	50 kA
Rated current = rated uninterrupted current [In = Iu]	400 A
Neutral conductor [% of phase conductor]	100 CSA
Overload trip [Ir ] 200 - 400 A Overload trip >Main pole [Ir ]	200 - 400 A
Short-circuit releases [Irm ] >Non-delayed [Ii = In x …]	200 - 400 A
Short-circuit releases [Irm ] >Delayed [Isd = Ir x …]	2 - 11
Standards	2 - 10
Protection against direct contact	IEC/EN 60947
Climatic proofing	Finger and back of hand proof to VDE 0106 Part 100
Ambient temperature >Ambient temperature, storage	Damp heat, constant, to IEC 60068-2-78 Damp heat, cyclic, to IEC 60068-2-30
Ambient temperature >Operation	- 40 - + 70 °C
Mechanical shock resistance (10 ms half-sinusoidal shock) according to IEC 60068-2-27	-25 - +70 °C
Safe isolation to EN 61140 >Between auxiliary contacts and main contacts	20 (half-sinusoidal shock 20 ms) g
Safe isolation to EN 61140 >between the auxiliary contacts	500 V AC
Weight	300 V AC
Mounting position	8.4 kg
Direction of incoming supply	Vertical and 90° in all directions   With XFI earth-fault release: - NZM1, N1, NZM2, N2: vertical and 90° in all directions with plug-in unit - NZM1, N1, NZM2, N2: vertical, 90° right/left with withdrawable unit: - NZM3, N3: vertical, 90° right/left - NZM4, N4: vertical with remote operator: - NZM2, N(S)2, NZM3, N(S)3, NZM4, N(S)4: vertical and 90° in all directions
Degree of protection >Device	as required
Degree of protection >Enclosures	In the operating controls area: IP20 (basic degree of protection)
Degree of protection >Terminations	With insulating surround: IP40 With door coupling rotary handle: IP66
Other technical data (sheet catalogue)	Tunnel terminal: IP10 Phase isolator and strip terminal: IP00
Rated current = rated uninterrupted current [In = Iu]	Temperature dependency, Derating
Rated surge voltage invariability [Uimp ] >Main contacts	400 A
Rated surge voltage invariability [Uimp ] >Auxiliary contacts	8000 V
Rated operational voltage [Ue]	6000 V
Overvoltage category/pollution degree	690 V AC
Rated insulation voltage [Ui ]	III/3
Use in unearthed supply systems	1000 V
Rated short-circuit making capacity [Icm ] >240 V [Icm ]	≦ 690 V
Rated short-circuit making capacity [Icm ] >400/415 V [Icm ]	187 kA
Rated short-circuit making capacity [Icm ] >440 V 50/60 Hz [Icm ]	105 kA
Rated short-circuit making capacity [Icm ] >525 V 50/60 Hz [Icm ]	74 kA
Rated short-circuit making capacity [Icm ] >690 V 50/60 H [Ic]	53 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >240 V 50/60 Hz [Icu ]	40 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >400/415 V 50/60 Hz [Icu ]	85 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >440 V 50/60 Hz [Icu ]	50 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >525 V 50/60 Hz [Icu ]	35 kA
Rated short-circuit breaking capacity Icn [Icn ] >Icu to IEC/EN 60947 test cycle O-t-CO [Icu] >690 V 50/60 Hz [Icu ]	25 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >240 V 50/60 Hz [Ics ]	20 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >400/415 V 50/60 Hz [Ics ]	85 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >440 V 50/60 Hz [Ics ]	50 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >525 V 50/60 Hz [Ics ]	35 kA
Rated short-circuit breaking capacity Icn [Icn ] >Ics to IEC/EN 60947 test cycle O-t-CO-t-CO [Ics] >690 V 50/60 Hz [Ics]	13 kA
Rated short-circuit breaking capacity Icn [Icn ]	5 kA
Rated short-time withstand current >t = 0.3 s [Icw ]	Maximum back-up fuse, if the expected short-circuit currents at the installation location exceed the switching capacity of the circuit-breaker.
Rated short-time withstand current >t = 1 s [Icw ]	3.3 kA
Utilization category to IEC/EN 60947-2	3.3 kA
Lifespan, mechanical(of which max. 50 % trip by shunt/undervoltage release) [Operations]	A
Lifespan, electrical >AC-1 >400 V 50/60 Hz [Operations]	15000
Lifespan, electrical >AC-1 >415 V 50/60 Hz [Operations]	5000
Lifespan, electrical >AC-1 >690 V 50/60 Hz [Operations]	5000
Lifespan, electrical >AC--3 >400 V 50/60 Hz [Operations]	3000
Lifespan, electrical >AC--3 >415 V 50/60 Hz [Operations]	2000
Lifespan, electrical >AC--3 >690 V 50/60 Hz [Operations]	2000
Lifespan, electrical >Max. operating frequency	2000
Total break time at short-circuit	60 Ops/h
Standard equipment	< 10 ms
Accessories required	Screw connection
Optional accessories	NZM3-4-XAVS
Round copper conductor >Box terminal >Solid	Box terminal Tunnel terminal connection on rear
Round copper conductor >Box terminal >Stranded	2 x 16 mm2
Round copper conductor >Tunnel terminal >Solid	1 x (35 - 240) 2 x (25-120) mm2
Round copper conductor >Tunnel terminal >Stranded >1-hole	1 x 16 mm2
Round copper conductor >Bolt terminal and rear-side connection >Direct on the switch >Solid	1 x (16 - 185) mm2
Round copper conductor >Bolt terminal and rear-side connection >Direct on the switch >Stranded	1 x 16 2 x 16 mm2
Round copper conductor >Bolt terminal and rear-side connection >Connection width extension >Connection width extension	1 x (25 - 240) 2 x (25 - 240) mm2
Al circular conductor >Tunnel terminal >Solid	2 x 300 mm2
Al circular conductor >Tunnel terminal >Stranded >Stranded	1 x 16 mm2
Al circular conductor >Tunnel terminal >Stranded >Double hole	1 x (25 - 185) 2) mm2
Al circular conductor >Tunnel terminal >Stranded	1 x (50 - 240) 2 x (50 - 240) mm2
Cu strip (number of segments x width x segment thickness) >Box terminal [min.]	2) Up to 240 mm² can be connected depending on the cable manufacturer.
Cu strip (number of segments x width x segment thickness) >Box terminal [max.]	6 x 16 x 0.8 mm
Cu strip (number of segments x width x segment thickness) >Bolt terminal and rear-side connection >Flat copper strip, with holes [min.]	10 x 24 x 1.0 + 5 x 24 x 1.0 (2 x) 8 x 24 x 1.0 mm
Cu strip (number of segments x width x segment thickness) >Bolt terminal and rear-side connection >Flat copper strip, with holes [max.]	6 x 16 x 0.8 mm
Cu strip (number of segments x width x segment thickness) >Bolt terminal and rear-side connection >Connection width extension	10 x 32 x 1.0 + 5 x 32 x 1.0 mm
Copper busbar (width x thickness) [mm] >Bolt terminal and rear-side connection >Screw connection	(2 x) 10 x 50 x 1.0 mm
Copper busbar (width x thickness) [mm] >Bolt terminal and rear-side connection >Direct on the switch [min.]	M10
Copper busbar (width x thickness) [mm] >Bolt terminal and rear-side connection >Direct on the switch [max.]	20 x 5 mm
Copper busbar (width x thickness) [mm] >Bolt terminal and rear-side connection >Connection width extension >Connection width extension [max.]	30 x 10 + 30 x 5 mm
Control cables	2 x (10 x 50) mm
Rated operational current for specified heat dissipation [In]	1 x (0.75 - 2.5) 2 x (0.75 - 1.5) mm2
Equipment heat dissipation, current-dependent [Pvid]	400 A
Operating ambient temperature min.	72 W
Operating ambient temperature max.	-25 °C
10.2 Strength of materials and parts >10.2.2 Corrosion resistance	+70 °C
10.2 Strength of materials and parts >10.2.3.1 Verification of thermal stability of enclosures	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.3.2 Verification of resistance of insulating materials to normal heat	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.3.3 Verification of resistance of insulating materials to abnormal heat and fire due to internal electric effects	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.4 Resistance to ultra-violet (UV) radiation	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.5 Lifting	Meets the product standard´s requirements.
10.2 Strength of materials and parts >10.2.6 Mechanical impact	Does not apply, since the entire switchgear needs to be evaluated.
10.2 Strength of materials and parts >10.2.7 Inscriptions	Does not apply, since the entire switchgear needs to be evaluated.
10.3 Degree of protection of ASSEMBLIES	Meets the product standard´s requirements.
10.4 Clearances and creepage distances	Does not apply, since the entire switchgear needs to be evaluated.
10.5 Protection against electric shock	Meets the product standard´s requirements.
10.6 Incorporation of switching devices and components	Does not apply, since the entire switchgear needs to be evaluated.
10.7 Internal electrical circuits and connections	Does not apply, since the entire switchgear needs to be evaluated.
10.8 Connections for external conductors	Is the panel builder´s responsibility.
10.9 Insulation properties >10.9.2 Power-frequency electric strength	Is the panel builder´s responsibility.
10.9 Insulation properties >10.9.3 Impulse withstand voltage	Is the panel builder´s responsibility.
10.9 Insulation properties >10.9.4 Testing of enclosures made of insulating material	Is the panel builder´s responsibility.
10.10 Temperature rise	Is the panel builder´s responsibility.
10.11 Short-circuit rating	The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.
10.12 Electromagnetic compatibility	Is the panel builder´s responsibility. The specifications for the switchgear must be observed.
10.13 Mechanical function	Is the panel builder´s responsibility. The specifications for the switchgear must be observed.
Rated permanent current Iu	The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.
Rated voltage	400 A
Rated short-circuit breaking capacity lcu at 400 V, 50 Hz	690 - 690 V
Overload release current setting	100 kA
Adjustment range short-term delayed short-circuit release	200 - 400 A
Adjustment range undelayed short-circuit release	400 - 4000 A
Integrated earth fault protection	800 - 4400 A
Type of electrical connection of main circuit	Yes
Device construction	Screw connection
Suitable for DIN rail (top hat rail) mounting	Built-in device slide-in technique (withdrawable)
DIN rail (top hat rail) mounting optional	No
Number of auxiliary contacts as normally closed contact	No
Number of auxiliary contacts as normally open contact	0
Number of auxiliary contacts as change-over contact	0
With switched-off indicator	0
With under voltage release	No
Number of poles	No
Position of connection for main current circuit	4
Type of control element	Front side
Complete device with protection unit	Rocker lever
Motor drive integrated	Yes
Motor drive optional	No
Degree of protection (IP)	Yes
Characteristic curve	IP20
Characteristic curve
Characteristic curve
Characteristic curve	Let-through current

As Mnelko, we are a reliable partner in industrial automation solutions, offering high-quality and innovative products with a wide product range to meet all the needs of your business. Our product portfolio consists of solutions designed based on the principles of high performance, durability, and efficiency to support modern industrial processes.
All of our products ensure maximum reliability even in challenging working conditions and help your business operations run smoothly. The products we offer in industrial automation, energy management, cabling solutions, and many other areas adapt flexibly to the needs of different sectors.
Additionally, our products are manufactured using only high-quality materials and comply with international standards. Through the solutions we provide, we enable our customers to increase operational efficiency and optimize costs. Our company closely follows technological advancements and continuously offers innovative products to help our customers gain a competitive advantage.
On each of our product pages, you can find comprehensive information about technical details, areas of use, and product features. You can explore all the products you need to strengthen your industrial processes on our website and enjoy a seamless purchasing experience.