SKU: Wago-750-484/040-000
2 kanallı analog giriş; 4 … 20 mA HART; Kendinden güvenli; Aşırı; mavi
This analog input module connects two field-side transformers equipped with a HART interface that are to be used in hazardous areas of Zone 0+1. The module supplies signal conditioners, reads process values via analog interface, and enables HART communication for configuring and importing dynamic variables.
The WAGO-I/O-SYSTEM 750 XTR must be installed either in Zone 2 or in a non-hazardous area.
The 24 V supply is derived from the power jumper contacts via multipliers to the field contacts (HART +).
The shield is directly connected to the DIN-rail.
The measurement input is equipped with current limitation, which limits the current to 25 mA. This module can supply the voltage for 2-wire signal conditioners.
Up to 4 HART dynamic variables (PV, SV, TV, QV) per channel can be mapped in the cyclic process image of the coupler or controller (parametrizable).
For HART communication with connected intelligent HART field devices, the HART protocol can be mapped in the cyclic process image of the coupler or controller (parametrizable).
FDT/DTM device drivers are available for select (programmable) couplers, allowing HART tool routing to the connected HART device.
The device is ideal for operation in harsh environments thanks to:
The analog input module must only be operated via 24 VDC Ex i XTR power supply (750-606/040-000)!
General information (e.g., installation regulations) on explosion protection is available in the WAGO-I/O-SYSTEM 750 XTR manuals!
This analog input module connects two field-side transformers equipped with a HART interface that are to be used in hazardous areas of Zone 0+1. The module supplies signal conditioners, reads process values via analog interface, and enables HART communication for configuring and importing dynamic variables.
The WAGO-I/O-SYSTEM 750 XTR must be installed either in Zone 2 or in a non-hazardous area.
The 24 V supply is derived from the power jumper contacts via multipliers to the field contacts (HART +).
The shield is directly connected to the DIN-rail.
The measurement input is equipped with current limitation, which limits the current to 25 mA. This module can supply the voltage for 2-wire signal conditioners.
Up to 4 HART dynamic variables (PV, SV, TV, QV) per channel can be mapped in the cyclic process image of the coupler or controller (parametrizable).
For HART communication with connected intelligent HART field devices, the HART protocol can be mapped in the cyclic process image of the coupler or controller (parametrizable).
FDT/DTM device drivers are available for select (programmable) couplers, allowing HART tool routing to the connected HART device.
The device is ideal for operation in harsh environments thanks to:
The analog input module must only be operated via 24 VDC Ex i XTR power supply (750-606/040-000)!
General information (e.g., installation regulations) on explosion protection is available in the WAGO-I/O-SYSTEM 750 XTR manuals!
| Number of analog inputs | 2 |
| Total number of channels (module) | 2 |
| Sinyal tipi | Current |
| Type of signal current | DC 4 … 20 mA |
| Sensor supply voltage | DC 16,5 V; Transmitter supply UV at 20 mA |
| Sensor connection | 2 x (2-conductor) |
| Giriş filtresi | Parametreleştirilebilir |
| Giriş filtresi: parametrelerle ayarlanabilir (kanal-kanal) | yes |
| Signal characteristic | Single-ended |
| Arıza teşhisi | Kablo kopması, ölçüm aralığı dışında |
| Çözünürlük [bit] | 12Bit |
| Güç tüketimi Pmax. | 1,60 W (slave´lerle (20 mA)) |
| Bit genişliği | 2 x 2 byte veri 2 x 2 byte veri + 2n x 4 byte veri (n = dinamik değişken adedi) 2 x 2 byte veri + 6 byte posta kutusu |
| Aşırı gerilim koruması | 30 V, ters polarite korumalı |
| Çevirme süresi (tip.) | 10ms |
| Messfehler, Bezugstemperatur | 25°C |
| Messfehler, Abweichung max. vom Messbereichsendwert | 0,2% |
| Temperaturfehler max. vom Messbereichsendwert | 0,01%/K |
| Kendinden güvenli Ex i | yes |
| System supply voltage | DC 5 V; via data contacts |
| Current consumption, system supply (5 V) | 25mA |
| Field supply voltage | DC 24 V; via power jumper contacts (Ex i XTR power supply: UO = max. 27.3 V) |
| Current consumption, field supply (module with no external load) | 26mA |
| Kanal başına HART aygıtları | 1 aygıt (single-drop, no multi-drop) |
| Kanal başına HART modemleri | 1 modem (multiplex değil) |
| Güç kaybı PV | 0,62 W (slave´siz) |
| İzolasyon | 300 VAC system/field |
| Dielektrik dayanımı | 510 VAC/775 VDC; per EN 60870-2-1 |
| Rated surge voltage | 1 kV; Rated surge voltage between intrinsically safe and non-intrinsically safe circuits: 1.5 kV (EN 60079-11) |
| Number of incoming power jumper contacts | 2 |
| Number of outgoing power jumper contacts | 2 |
| Current carrying capacity of the power jumper contacts | 1A |
| ATEX Guideline | EN/IEC 60079-0, -7, -11 |
| Elektrik şebekesi, güvenliğe ilişkin bilgi | Uo = 26,8 V; Io = 90,07 mA; Po = 603,5 mW; Kennlinie: Linear |
| Reaktans Ex ia IIC | Lo = 1,8 mH; Co = 0,092 μF |
| Reaktans Ex ia IIB | Lo = 16 mH; Co = 0,72 μF |
| Reaktans Ex ia IIA | Lo = 27 mH; Co = 2.37 μF |
| Reaktans Ex ia I | Lo = 38 mH; Co = 3,85 µF |
| Reaktans | (The above-listed ratings do not account for the coincidental occurrence of capacitances and inductances. For ratings taking the coincidental occurrence of capacitances and inductances into account, see manual) |
| Connection technology: In-/Outputs | 16 x CAGE CLAMP® |
| Connection type (1) | Inputs/Outputs |
| Tek damarlı boylar | 0,25 … 2,5 mm² / 24 … 14 AWG |
| İnce bükümlü kablolar | 0,25 … 2,5 mm² / 24 … 14 AWG |
| Sıyırma uzunluğu | 8 … 9 mm / 0.31 … 0.35 inch |
| Width | 24 mm / 0.945 inch |
| Height | 67,8 mm / 2.669 inch |
| DIN rayın üst kenarından yükseklik | 60,6 mm / 2.386 inch |
| Depth | 100 mm / 3.937 inch |
| Montaj tipi | DIN 35 ray |
| Renk | mavi |
| Gövde malzemesi | Polycarbonate, polyamide 6.6 |
| Ağırlık | 92,9 |
| Uygunluk işareti | CE |
| Surrounding air (operating) temperature | -40 … 70 °C |
| Surrounding air (storage) temperature | -40 … 85 °C |
| Koruma sınıfı | IP20 |
| Kirlilik derecesi (5) | 2 per IEC 61131-2 |
| Çalışma yüksekliği | without temperature derating: 0 … 2000 m; with temperature derating: 2000 … 5000 m (0.5 K/100 m); max.: 5000 m |
| Montaj pozisyonu | horizontal (standing/lying) or vertical |
| Nısbi nem (yoğuşmasız) | 95% |
| Relative humidity | Short-term condensation per Class 3K7/IEC EN 60721-3-3 and E DIN 40046-721-3 (except wind-driven precipitation, water and ice formation) |
| Titreşime dayanıklı | acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3 |
| Darbe direnci | per IEC 60068-2-27 (15g/11 ms/half-sine/1,000 shocks; 25g/6 ms/1,000 shocks), EN 61373 |
| EMV-Störfestigkeit | acc. to EN 61000-6-1, -2, EN 61131-2, marine applications, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994 |
| EMU: |
acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3 |
| Kirletici maddelere maruziyet | Per IEC 60068-2-42 and IEC 60068-2-43 |
| Permissible H2S contaminant concentration at a relative humidity |
10ppm |
| Permissible SO2 contaminant concentration at a relative humidity |
25ppm |
| SAP´den ambalaj tipi | BOX |
| Country of origin | DE |
| GTIN | 4055143649506 |
| Customs Tariff No. | 85389099990 |
Tüm hakları saklıdır. Mnelko Endüstriyel San. ve Tic.Ltd.Şti. 2024